
.. _sec-spectrum-module:

Spectrum Module
---------------

.. include:: replace.txt
.. highlight:: cpp

.. heading hierarchy:
   ------------- Chapter
   ************* Section (#.#)
   ============= Subsection (#.#.#)
   ############# Paragraph (no number)





The Spectrum module aims at providing support for modeling the frequency-dependent
aspects of communications in |ns3|.
The model was first introduced in
[Baldo2009Spectrum]_, and has been enhanced and refined over the years.



.. _fig-spectrum-analyzer-example:

.. figure:: figures/spectrum-analyzer-example.*
   :align: center

   Spectrogram produced by a spectrum analyzer in a scenario
   involving wifi signals interfered by a microwave oven, as simulated
   by the example ``adhoc-aloha-ideal-phy-with-microwave-oven``.


Model Description
*****************

The module provides:

* a set of classes for modeling signals and

* a Channel/PHY interface based on a power spectral density
  signal representation that is technology-independent

* two technology-independent Channel implementations based on the Channel/PHY interface

* a set of basic PHY model implementations based on the Channel/PHY interface

The source code for the spectrum module is located at ``src/spectrum``.


Design
======


Signal model
############

The signal model is implemented by the
``SpectrumSignalParameters`` class. This class provides the following
information for a signal being transmitted/received by PHY devices:

* a reference to the transmitting PHY device

* a reference to the antenna model used by the transmitting PHY device
  to transmit this signal

* the duration of the signal

* its Power Spectral Density (PSD) of the signal, which is assumed to be constant for
  the duration of the signal.

The PSD is represented as a set of discrete scalar values each
corresponding to a certain subband in frequency. The set of frequency subbands
to which the PSD refers to is defined by an instance of the
``SpectrumModel`` class. The PSD itself is implemented as an instance
of the ``SpectrumValue`` class which contains a reference to the
associated ``SpectrumModel`` class instance. The ``SpectrumValue``
class provides several arithmetic operators to allow to perform calculations
with PSD instances. Additionally, the ``SpectrumConverter`` class
provides means for the conversion of ``SpectrumValue`` instances from
one ``SpectrumModel`` to another.

For a more formal mathematical description of the signal model just
described, the reader is referred to [Baldo2009Spectrum]_.

The ``SpectrumSignalParameters`` class is meant to include only
information that is valid for all signals; as such, it is not meant to
be modified to add technology-specific information (such as type of
modulation and coding schemes used, info on preambles and reference
signals, etc). Instead, such information shall be put in a new class
that inherits from ``SpectrumSignalParameters`` and extends it with
any technology-specific information that is needed. This design
is intended to model the fact that in the real world we have signals
of different technologies being simultaneously transmitted and
received over the air.



Channel/PHY interface
#####################

The spectrum Channel/PHY interface is defined by the base classes ``SpectrumChannel``
and ``SpectrumPhy``. Their interaction simulates the transmission and
reception of signals over the medium. The way this interaction works is depicted in :ref:`fig-spectrum-channel-phy-interface`:


.. _fig-spectrum-channel-phy-interface:

.. figure:: figures/spectrum-channel-phy-interface.*
   :align: center

   Sequence diagram showing the interaction between SpectrumPhy and SpectrumChannel



Spectrum Channel implementations
################################

The module provides two ``SpectrumChannel`` implementations:
``SingleModelSpectrumChannel`` and ``MultiModelSpectrumChannel``. They
both provide this functionality:

 * Propagation loss modeling, in two forms:

   - you can plug models based on ``PropagationLossModel`` on these
     channels. Only linear models (where the loss value does not
     depend on the transmission power) can be used.
     These models are single-frequency in the sense that the loss value is
     applied equally to all components of the power spectral density.

   - you can plug models based on ``SpectrumPropagationLossModel`` on these
     channels. These models can have frequency-dependent loss, i.e.,
     a separate loss value is calculated and applied to each component
     of the power spectral density.

 * Propagation delay modeling, by plugging a model based on
   ``PropagationDelayModel``. The delay is independent of frequency and
   applied to the signal as a whole. Delay modeling is implemented by
   scheduling the ``StartRx`` event with a delay respect to the
   ``StartTx`` event.

``SingleModelSpectrumChannel`` and ``MultiModelSpectrumChannel`` are
quite similar, the main difference is that
``MultiModelSpectrumChannel`` allows to use different
``SpectrumModel`` instances with the same channel instance, by
automatically taking care of the conversion of PSDs among the
different models.



.. _sec-example-model-implementations:

Example model implementations
#############################


The spectrum module provides some basic implementation of several components that
are mainly intended as a proof-of-concept and as an example for
building custom models with the spectrum module. Here is a brief list
of the available implementations:

 * ``SpectrumModel300Khz300GhzLog`` and
   ``SpectrumModelIsm2400MhzRes1Mhz`` are two example ``SpectrumModel`` implementations

 * ``HalfDuplexIdealPhy``: a basic PHY model using a gaussian
   interference model (implemented in ``SpectrumInterference``)
   together with an error model based on Shannon capacity (described
   in [Baldo2009Spectrum]_ and implemented in ``SpectrumErrorModel``. This PHY
   uses the ``GenericPhy`` interface. Its addditional custom signal
   parameters are defined in ``HalfDuplexIdealPhySignalParameters``.

 * ``WifiSpectrumValueHelper`` is an helper object that makes it easy
   to create ``SpectrumValues`` representing PSDs and RF filters for
   the wifi technology.

 * ``AlohaNoackNetDevice``: a minimal NetDevice that allows to send
   packets over ``HalfDuplexIdealPhy`` (or other PHY model based on
   the  ``GenericPhy`` interface).

 * ``SpectrumAnalyzer``, ``WaveformGenerator`` and ``MicrowaveOven`` are examples of PHY
   models other than communication devices - the names should be
   self-explaining.








References
==========

.. [Baldo2009Spectrum] N. Baldo and M. Miozzo, "Spectrum-aware Channel and PHY layer modeling for ns3",
   Proceedings of ICST NSTools 2009, Pisa, Italy




Usage
*****

The main use case of the spectrum model is for developers who want to
develop a new model for the PHY layer of some wireless technology to
be used within ns-3.
Here are some notes on how the spectrum module is expected to be used.

 * ``SpectrumPhy`` and ``SpectrumChannel`` are abstract base classes. Real
   code will use classes that inherit from these classes.

 * If you are implementing a new model for some wireless
   technology of your interest, and want to use the spectrum module,
   you'll typically create your own module and make it depend on the
   spectrum module. Then you typically have to implement:

    - a child class of ``SpectrumModel`` which defines the (sets of) frequency
      subbands used by the considered wireless technology. **Note**:
      instances of ``SpectrumModel`` are typically statically allocated,
      in order to allow several ``SpectrumValue`` instances to reference
      the same ``SpectrumModel`` instance.

    - a child class of ``SpectrumPhy`` which will handle transmission and
      reception of signals (including, if appropriate, interference
      and error modeling).

    - a child class of ``SpectrumSignalParameters`` which will contain
      all the information needed to model the signals for the wireless
      technology being considered that is not already provided by the
      base ``SpectrumSignalParameters`` class. Examples of such
      information are the type of modulation and coding schemes used,
      the PHY preamble format, info on the pilot/reference signals, etc.

 * The available ``SpectrumChannel`` implementations
   (``SingleModelSpectrumChannel`` and ``MultiModelSpectrumChannel``,
   are quite generic. Chances are you can use them as-is. Whether you
   prefer one or the other it is just a matter of whether you will
   have a single SpectrumModel or multiple ones in your
   simulations.

 * Typically, there will be a single SpectrumChannel instance to which
   several SpectrumPhy instances are plugged. The rule of thumb is
   that all PHYs that are interfering with each other shall be plugged
   on the same channel. Multiple SpectrumChannel instances are
   expected to be used mainly when simulating completely orthogonal
   channels; for example, when simulating the uplink and downlink
   of a Frequency Division Duplex system, it is a good choice to use
   two SpectrumChannel instances in order to reduce computational
   complexity.

 * Different types of SpectrumPhy (i.e., instances of different child
   classes) can be plugged on the same SpectrumChannel instance. This
   is one of the main features of the
   spectrum module, to support inter-technology interference. For
   example, if you implement a WifiSpectrumPhy and a
   BluetoohSpectrumPhy, and plug both on a SpectrumChannel, then you'll
   be able to simulate interference between wifi and bluetooth and
   vice versa.

 * Different child classes of ``SpectrumSignalParameters`` can coexist
   in the same simulation, and be transmitted over the same channel
   object.  Again, this is part of the support for inter-technology
   interference. A PHY device model is expected to use the
   ``DynamicCast<>`` operator to determine if a signal is of a certain
   type it can attempt to receive. If not, the signal is normally
   expected to be considered as interference.




Helpers
=======


The helpers provided in ``src/spectrum/helpers`` are mainly intended
for the example implementations described in :ref:`sec-example-model-implementations`.
If you are developing your custom model based on the
spectrum framework, you will probably prefer to define your own
helpers.



Attributes
==========


 * Both ``SingleModelSpectrumChannel`` and
   ``MultiModelSpectrumChannel`` have an attribute ``MaxLossDb`` which
   can use to avoid propagating signals affected by very high
   propagation loss. You can use this to reduce the complexity of
   interference calculations. Just be careful to choose a value that
   does not make the interference calculations inaccurate.

 * The example implementations described in :ref:`sec-example-model-implementations` also have several attributes.





Output
======


 * Both ``SingleModelSpectrumChannel`` and
   ``MultiModelSpectrumChannel`` provide a trace source called
   ``PathLoss`` which is fired whenever a new path loss value is
   calclulated. **Note**: only single-frequency path loss is accounted
   for, see the attribute description.

 * The example implementations described in :ref:`sec-example-model-implementations` also provide some trace sources.

 * The helper class ``SpectrumAnalyzerHelper`` can be conveniently
   used to generate an output text file containing the spectrogram
   produced by a SpectrumAnalyzer instance. The format is designed to
   be easily plotted with ``gnuplot``. For example, if your run the
   example ``adhoc-aloha-ideal-phy-with-microwave-oven`` you will get
   an output file called ``spectrum-analyzer-output-3-0.tr``. From
   this output file, you can generate a figure similar to
   :ref:`fig-spectrum-analyzer-example` by executing the following
   gnuplot commands:

.. sourcecode:: none

    unset surface
    set pm3d at s
    set palette
    set key off
    set view 50,50
    set xlabel "time (ms)"
    set ylabel "freq (MHz)"
    set zlabel "PSD (dBW/Hz)" offset 15,0,0
    splot "./spectrum-analyzer-output-3-0.tr" using ($1*1000.0):($2/1e6):(10*log10($3))



Examples
========


The example programs in ``src/spectrum/examples/`` allow to see the
example implementations described in :ref:`sec-example-model-implementations` in action.


Troubleshooting
===============

 * **Disclaimer on inter-technology interference**: the spectrum model
   makes it very easy to implement an inter-technology interference
   model, but this does not guarantee
   that the resulting model is accurate. For example, the gaussian
   interference model implemented in the ``SpectrumInterference`` class can be used
   to calculate inter-technology interference, however the results might not be valid in some
   scenarios, depending on the actual waveforms involved, the number
   of interferers, etc. Moreover, it is very important to use error
   models that are consistent with the interference model. The
   responsibility of ensuring that the models being used are correct
   is left to the user.





Testing
*******

In this section we describe the test suites that are provided within
the spectrum module.

SpectrumValue test
==================

The test suite ``spectrum-value`` verifies the correct functionality of the arithmetic
operators implemented by the ``SpectrumValue`` class. Each test case
corresponds to a different operator. The test passes if the result
provided by the operator implementation is equal to the reference
values which were calculated offline by hand. Equality is verified
within a tolerance of :math:`10^{-6}` which is to account for
numerical errors.


SpectrumConverter test
======================

The test suite ``spectrum-converter`` verifies the correct
functionality of the ``SpectrumConverter`` class. Different test cases
correspond to the conversion of different ``SpectrumValue`` instances
to different ``SpectrumModel`` instances. Each test passes if the
``SpectrumValue`` instance resulting from the conversion is equal to the reference
values which were calculated offline by hand. Equality is verified
within a tolerance of :math:`10^{-6}` which is to account for
numerical errors.


Describe how the model has been tested/validated.  What tests run in the
test suite?  How much API and code is covered by the tests?  Again,
references to outside published work may help here.




Interference test
=================

The test suite ``spectrum-interference`` verifies the correct
functionality of the ``SpectrumInterference`` and
``ShannonSpectrumErrorModel`` in a scenario involving four
signals (an intended signal plus three interferers). Different test
cases are created corresponding to different PSDs of the intended
signal and different amount of transmitted bytes. The test passes if
the output of the error model (successful or failed) coincides with
the expected one which was determine offline by manually calculating
the achievable rate using Shannon's formula.


IdealPhy test
=============

The test verifies that ``AlohaNoackNetDevice`` and
``HalfDuplexIdealPhy`` work properly when installed in a node. The
test recreates a scenario with two nodes (a TX and a RX) affected by a path loss such
that a certain SNR is obtained. The TX node transmits with a
pre-determined PHY rate and with an application layer rate which is
larger than the PHY rate, so as to saturate the
channel. ``PacketSocket`` is used in order to avoid protocol
overhead. Different
test cases correspond to different PHY rate and SNR values. For each
test case, we calculated offline (using Shannon's formula) whether
the PHY rate is achievable or not. Each test case passes if the
following conditions are satisfied:

 * if the PHY rate is achievable, the application throughput shall be within
   :math:`1\%` of the PHY rate;

 * if the PHY rate is not achievable, the application throughput shall
   be zero.




Additional Models
*****************

TV Transmitter Model
====================

A TV Transmitter model is implemented by the ``TvSpectrumTransmitter`` class.
This model enables transmission of realistic TV signals to be simulated and can
be used for interference modeling. It provides a customizable power spectral
density (PSD) model, with configurable attributes including the type of
modulation (with models for analog, 8-VSB, and COFDM), signal bandwidth,
power spectral density level, frequency, and transmission duration. A helper
class, ``TvSpectrumTransmitterHelper``, is also provided to assist users in
setting up simulations.

Main Model Class
################

The main TV Transmitter model class, ``TvSpectrumTransmitter``, provides a
user-configurable PSD model that can be transmitted on the ``SpectrumChannel``.
It inherits from ``SpectrumPhy`` and is comprised of attributes and methods to
create and transmit the signal on the channel.

.. _spectrum-tv-cofdm:

.. figure:: figures/spectrum-tv-cofdm.*
   :align: center

   8K COFDM signal spectrum generated from ``TvSpectrumTransmitter`` (Left) and
   theoretical COFDM signal spectrum [KoppCOFDM]_ (Right)

One of the user-configurable attributes is the type of modulation for the TV
transmitter to use. The options are 8-VSB (Eight-Level Vestigial Sideband
Modulation) which is notably used in the North America ATSC digital television
standard, COFDM (Coded Orthogonal Frequency Division Multiplexing) which is
notably used in the DVB-T and ISDB-T digital television standards adopted by
various countries around the world, and analog modulation which is a legacy
technology but is still being used by some countries today. To accomplish
realistic PSD models for these modulation types, the signals’ PSDs were
approximated from real standards and developed into models that are scalable by
frequency and power. The COFDM PSD is approximated from Figure 12 (8k mode) of
[KoppCOFDM]_, the 8-VSB PSD is approximated from Figure 3 of [Baron8VSB]_, and the
analog PSD is approximated from Figure 4 of [QualcommAnalog]_. Note that the
analog model is approximated from the NTSC standard, but other analog modulation
standards such as PAL have similar signals. The approximated COFDM PSD model is
in 8K mode. The other configurable attributes are the start frequency,
signal/channel bandwidth, base PSD, antenna type, starting time,
and transmit duration.

``TvSpectrumTransmitter`` uses ``IsotropicAntennaModel`` as its antenna model by
default, but any model that inherits from ``AntennaModel`` is selectable, so
directional antenna models can also be used. The propagation loss models used
in simulation are configured in the ``SpectrumChannel`` that the user chooses to
use. Terrain and spherical Earth/horizon effects may be supported in future ns-3
propagation loss models.

After the attributes are set, along with the ``SpectrumChannel``,
``MobilityModel``, and node locations, the PSD of the TV transmitter signal can
be created and transmitted on the channel.

.. _sec-tv-helper-class:

Helper Class
############

The helper class, ``TvSpectrumTransmitterHelper``, consists of features to
assist users in setting up TV transmitters for their simulations. Functionality
is also provided to easily simulate real-world scenarios.

.. _spectrum-tv-8vsb:

.. figure:: figures/spectrum-tv-8vsb.*
   :align: center

   North America ATSC channel 19 & 20 signals generated using
   ``TvSpectrumTransmitterHelper`` (Left) and theoretical 8-VSB signal
   [Baron8VSB]_ (Right). Note that the theoretical signal is not shown in dB
   while the ns-3 generated signals are.

Using this helper class, users can easily set up TV transmitters right after
configuring attributes. Multiple transmitters can be created at a time. Also
included are real characteristics of specific geographic regions that can be
used to run realistic simulations. The regions currently included are
North America, Europe, and Japan. The frequencies and bandwidth of each TV
channel for each these regions are provided.

.. _spectrum-tv-rand-geo-points:

.. figure:: figures/spectrum-tv-rand-geo-points.*
   :align: center

   Plot from MATLAB implementation of CreateRegionalTvTransmitters method in
   ``TvSpectrumTransmitterHelper``. Shows 100 random points on Earth’s surface
   (with altitude 0) corresponding to TV transmitter locations within a 2000 km
   radius of 35° latitude and -100° longitude.

A method (CreateRegionalTvTransmitters) is provided that enables users to
randomly generate multiple TV transmitters from a specified region with a given
density within a chosen radius around a point on Earth’s surface. The region,
which determines the channel frequencies of the generated TV transmitters, can
be specified to be one of the three provided, while the density determines the
amount of transmitters generated. The TV transmitters' antenna heights
(altitude) above Earth's surface can also be randomly generated to be within a
given maximum altitude. This method models Earth as a perfect sphere, and
generated location points are referenced accordingly in Earth-Centered
Earth-Fixed Cartesian coordinates. Note that bodies of water on Earth are not
considered in location point generation--TV transmitters can be generated
anywhere on Earth around the origin point within the chosen maximum radius.

Examples
########

Two example simulations are provided that demonstrate the functionality of the
TV transmitter model. ``tv-trans-example`` simulates two 8-VSB TV transmitters
with adjacent channel frequencies. ``tv-trans-regional-example`` simulates
randomly generated COFDM TV transmitters (modeling the DVB-T standard)
located around the Paris, France area with channel frequencies and bandwidths
corresponding to the European television channel allocations.

Testing
#######

The ``tv-spectrum-transmitter`` test suite verifies the accuracy of the
spectrum/PSD model in ``TvSpectrumTransmitter`` by testing if the maximum power
spectral density, start frequency, and end frequency comply with expected values
for various test cases.

The ``tv-helper-distribution`` test suite verifies the functionality of the
method in ``TvSpectrumTransmitterHelper`` that generates a random number of TV
transmitters based on the given density (low, medium, or high) and maximum
number of TV channels. It verifies that the number of TV transmitters generated
does not exceed the expected bounds.

The CreateRegionalTvTransmitters method in ``TvSpectrumTransmitterHelper``
described in :ref:`sec-tv-helper-class` uses two methods from the
``GeographicPositions`` class in the Mobility module to generate the random
Cartesian points on or above earth's surface around an origin point which
correspond to TV transmitter positions. The first method converts Earth
geographic coordinates to Earth-Centered Earth-Fixed (ECEF) Cartesian
coordinates, and is tested in the ``geo-to-cartesian`` test suite by comparing
(with 10 meter tolerance) its output with the output of the geographic to ECEF
conversion function [MatlabGeo]_ of the MATLAB Mapping Toolbox for numerous
test cases. The other used method generates random ECEF Cartesian points around
the given geographic origin point, and is tested in the ``rand-cart-around-geo``
test suite by verifying that the generated points do not exceed the given
maximum distance radius from the origin point.

3GPP TR 38.901 fast fading model
================================
The framework described by TR 38.901 [TR38901]_ is a 3D statistical Spatial
Channel Model supporting different propagation environments (e.g., urban,
rural, indoor), multi-antenna operations and the modeling of wireless channels
between 0.5 and 100 GHz.
The overall channel is represented by the matrix :math:`H(t,\tau)`, in which each
entry H :sub:`u,s` :math:`(t,\tau)` corresponds to the impulse response of the channel between the
s-th element of the transmitting antenna and the u-th element of the receiving
antenna. H :sub:`u,s` :math:`(t,\tau)` is generated by the superposition of N different multi-path
components, called clusters, each of which composed of M different rays.
The channel matrix generation procedure accounts for large and small scale
propagation phenomena. The classes ThreeGppSpectrumPropagationLossModel and
ThreeGppChannelModel included in the spectrum module takes care of the generation
of the channel coefficients and the computation of the frequency-dependent
propagation loss.

Implementation
##############

Our implementation is described in [Zugno]_. It is based on the model described
in [Zhang]_, but the code has been refactored, extended, and aligned to TR 38.901
[TR38901]_.
The fundamental assumption behind this model is the channel reciprocity, i.e.,
the impulse response of the channel between node a and node b is the same as
between node b and node a.
To deal with the equivalence of the channel between a and b, no matter who is
the transmitter and who is the receiver, the model considers the pair of nodes
to be composed by one "s" and one "u" node. The channel matrix, as well as other
parameters, are saved and used under the assumption that, within a pair, the
definition of the "s" and "u" node will always be the same. For more details,
please have a look at the documentation of the classes
ThreeGppChannelModel and ThreeGppSpectrumPropagationLossModel.

**Note:**

  * Currently, no error model is provided; a link-to-system campaign may be
    needed to incorporate it in existing modules.

  * The model does not include any spatial consistency update procedure
    (see [TR38901]_, Sec. 7.6.1). The implementation of this feature is left
    as future work.

  * Issue regarding the blockage model: according to 3GPP TR 38.901 v15.0.0
    (2018-06) section 7.6.4.1, the blocking region for self-blocking is provided
    in LCS.
  
    However, here, clusterAOA and clusterZOA are in GCS and blocking check is
    performed for self-blocking similar to non-self blocking, that is in GCS.
    One would expect the angles to be transposed to LCS before checking
    self-blockage.
  

ThreeGppSpectrumPropagationLossModel
####################################

The class ThreeGppSpectrumPropagationLossModel extends the SpectrumPropagationLossModel
interface and enables the modeling of frequency
dependent propagation phenomena. The main method is DoCalcRxPowerSpectralDensity,
which takes as input the power spectral density (PSD) of the transmitted signal,
the mobility models of the transmitting node and receiving node, and
returns the PSD of the received signal.

Procedure used to compute the PSD of to compute the PSD of the received signal:

1. Retrieve the beamforming vectors
To account for the beamforming, ThreeGppSpectrumPropagationLossModel has to
retrieve the beamforming vectors of the transmitting and receiving antennas.
The method DoCalcRxPowerSpectralDensity uses m_deviceAntennaMap to obtain the
antenna objects associated to the transmitting and receiving devices, and calls
the method GetCurrentBeamformingVector to retrieve the beamforming vectors.
For each device using the channel, the m_deviceAntennaMap contains the associated
antenna object of type ThreeGppAntennaArrayModel. Since the mapping is one-to-one,
the model supports a single antenna object for each device.
The m_deviceAntennaMap has to be initialized by inserting the device-antenna
pairs using the method AddDevice.

2. Retrieve the channel matrix
The ThreeGppSpectrumPropagationLossModel relies on the ThreeGppChannelModel class
to obtain the channel matrix. In particular, it makes use of the method GetChannel,
which returns a ChannelMatrix object containing the channel
matrix and other channel parameters.
The ThreeGppChannelModel instance is automatically
created in the the ThreeGppSpectrumPropagationLossModel constructor and it can
be configured using the method SetChannelModelAttribute ().

4. Compute the long term component
The method GetLongTerm returns the long term component obtained by multiplying
the channel matrix and the beamforming vectors. To reduce the computational
load, the long term components associated to the different channels are
stored in the m_longTermMap and recomputed only if the associated channel
matrix is updated or if the transmitting and/or receiving beamforming vectors
have changed. Given the channel reciprocity assumption, for each node pair a
single long term component is saved in the map.

5. Apply the small scale fading and compute the channel gain
The method CalcBeamformingGain computes the channel gain in each sub-band and
applies it to the PSD of the transmitted signal to obtain the received PSD.
To compute the sub-band gain, it accounts for the Doppler phenomenon and the
time dispersion effect on each cluster.
In order to reduce the computational load, the Doppler component of each
cluster is computed considering only the central ray.

ThreeGppChannelModel
####################

The class ThreeGppChannelModel implements the channel matrix generation procedure
described in Sec. of [TR38901]_.
The main method is GetChannel, which takes as input the mobility models of
the transmitter and receiver nodes, the associated antenna objects,
and returns a ChannelMatrix object containing:

* the channel matrix of size UxSxN, where U is the number of receiving antenna elements, S is the number of transmitting antenna elements and N is the number of clusters

* the clusters delays, as an array of size N

* the clusters arrival and departure angles, as a 2D array in which each row corresponds to a direction (AOA, ZOA, AOD, ZOD) and each column corresponds to a different cluster

* a time stamp indicating the time at which the channel matrix was generated

* the node IDs

* other channel parameters

The ChannelMatrix objects are saved
in the map m_channelMap and updated when the coherence time
expires, or in case the LOS/NLOS channel condition changes.
The coherence time can be configured through
the attribute "UpdatePeriod", and should be chosen by taking into account all the
factors that affects the channel variability, such as mobility, frequency,
propagation scenario, etc. By default, it is set to 0, which means that the
channel is recomputed only when the LOS/NLOS condition changes.
It is possible to configure the propagation scenario and the operating frequency
of interest through the attributes "Scenario" and "Frequency", respectively.

**Blockage model:** 3GPP TR 38.901 also provides an optional
feature that can be used to model the blockage effect due to the
presence of obstacles, such as trees, cars or humans, at the level
of a single cluster. This differs from a complete blockage, which
would result in an LOS to NLOS transition. Therefore, when this
feature is enabled, an additional attenuation is added to certain
clusters, depending on their angle of arrival. There are two possi-
ble methods for the computation of the additional attenuation, i.e.,
stochastic (Model A) and geometric (Model B). In this work, we
used the implementation provided by [Zhang]_, which
uses the stochastic method. In particular, the model is implemented by the
method CalcAttenuationOfBlockage, which computes the additional attenuation.
The blockage feature can be disable through the attribute "Blockage". Also, the
attributes "NumNonselfBlocking", "PortraitMode" and "BlockerSpeed" can be used
to configure the model.

Testing
#######
The test suite ThreeGppChannelTestSuite includes three test cases:

* ThreeGppChannelMatrixComputationTest checks if the channel matrix has the
  correct dimensions and if it correctly normalized

* ThreeGppChannelMatrixUpdateTest, which checks if the channel matrix
  is correctly updated when the coherence time exceeds

* ThreeGppSpectrumPropagationLossModelTest, which tests the functionalities
  of the class ThreeGppSpectrumPropagationLossModel. It builds a simple
  network composed of two nodes, computes the power spectral density
  received by the receiving node, and
  
    1. Checks if the long term components for the direct and
       the reverse link are the same,
    2. Checks if the long term component is updated when changing
       the beamforming vectors,
    3. Checks if the long term is updated when changing the channel matrix


**Note:** TR 38.901 includes a calibration procedure that can be used to validate
the model, but it requires some additional features which are not currently
implemented, thus is left as future work.

References
##########

.. [Baron8VSB] Baron, Stanley. "First-Hand:Digital Television: The Digital
   Terrestrial Television Broadcasting (DTTB) Standard." IEEE Global History
   Network. <http://www.ieeeghn.org/wiki/index.php/First-Hand:Digital_Television:_The_Digital_Terrestrial_Television_Broadcasting_(DTTB)_Standard>.

.. [KoppCOFDM] Kopp, Carlo. "High Definition Television." High Definition
   Television. Air Power Australia. <http://www.ausairpower.net/AC-1100.html>.

.. [MatlabGeo] "Geodetic2ecef." Convert Geodetic to Geocentric (ECEF)
   Coordinates. The MathWorks, Inc.
   <http://www.mathworks.com/help/map/ref/geodetic2ecef.html>.

.. [QualcommAnalog] Stephen Shellhammer, Ahmed Sadek, and Wenyi Zhang.
   "Technical Challenges for Cognitive Radio in the TV White Space Spectrum."
   Qualcomm Incorporated.

.. [TR38901] 3GPP. 2018. TR 38.901. Study on channel for frequencies from 0.5 to
   100 GHz. V.15.0.0. (2018-06).

.. [Zhang] Menglei Zhang, Michele Polese, Marco Mezzavilla, Sundeep Rangan,
   Michele Zorzi. "ns-3 Implementation of the 3GPP MIMO Channel Model for
   Frequency Spectrum above 6 GHz". In Proceedings of the Workshop on ns-3
   (WNS3 '17). 2017.

.. [Zugno] Tommaso Zugno, Michele Polese, Natale Patriciello, Biljana Bojovic,
   Sandra Lagen, Michele Zorzi. "Implementation of a Spatial Channel Model for
   ns-3". Submitted to the Workshop on ns-3 (WNS3 '20). 2020.
   Available: https://arxiv.org/abs/2002.09341
